Thursday, July 2, 2026

Login
Register

No Result

View All Result

No Result

View All Result

No Result

View All Result

ADVERTISEMENT

Notifications

Clear all

Siemens NX

Page 1 / 3 Next

Change the drawing view to another view later in Siemens NX drafting

Last post by Greg, 2 years ago

Posts: 3

Views: 2752

Is it possible to change the selected drawing view...

By Alex 5 years ago
What CAD software has that functionality?

By Noah 5 years ago
In PTC Creo has that feature functionality. Indivi...

By Greg 2 years ago

Can I export macro file embedded to Siemens NX

Last post by Jerry, 2 years ago

Posts: 1

Views: 843

How do I export the macro file, which already embe...

By Jerry 2 years ago

Siemens NX give " Fatal error detected - unable to continue. Unhandled operating system,.."

Last post by Volker, 3 years ago

Posts: 1

Views: 2679

Hey, in recent I get following error massage and...

By Volker 3 years ago

"Pattern master is minimally loaded" error in Siemens NX assembly selection

Last post by Thelonious, 3 years ago

Posts: 2

Views: 3195

Hey, in my NX assembly I deleted few assembly pa...

By Peter 3 years ago
You should have open the relevant assembly part in...

By Theloniou... 3 years ago

How do I find the Center of Gravity in assembly model in Siemens NX

Last post by Peter, 3 years ago

Posts: 1

Views: 1964

I'm modeling drone design and with lot assembly co...

By Peter 3 years ago

"Cannot trim off middle section of an offset curve" Trim Curve Issue in NX Drafting

Last post by Peter, 3 years ago

Posts: 1

Views: 2319

In Siemens NX sketching, how do I trim off set cur...

By Peter 3 years ago

NX 1953 add dimension relation in sketch

Last post by Thelonious, 3 years ago

Posts: 2

Views: 2318

In NX 1953 version , how do I add dimension relati...

By Roy 3 years ago
You can assign expression to each dimension line b...

By Theloniou... 3 years ago

Drawing Spiral Curve in NX

Last post by Roy, 3 years ago

Posts: 1

Views: 1889

I'm modeling Cyclone separator along with Siemens ...

By Roy 3 years ago

STL file export setting for better quality in NX

Last post by Dhaval, 4 years ago

Posts: 3

Views: 3590

What are the better export setting, that you are u...

By Dhaval 4 years ago
It has been said, that to keep Set Output typ...

By Yoda 4 years ago
Thank you, anyhow what should be the "Angular Tole...

By Dhaval 4 years ago

Does line width of curves has an effect?

Last post by Yoda, 4 years ago

Posts: 4

Views: 3483

In NX curves can be assigned with different line w...

By Broad 4 years ago
No effect, the line width/colors only for visible ...

By Yoda 4 years ago
I see, then how we set all the default line width ...

By Broad 4 years ago
See the post, Changing default line/curve width ...

By Yoda 4 years ago

Changing default line/curve width in NX 1926

Last post by Thelonious, 4 years ago

Posts: 4

Views: 4956

Is it possible to change the default system width ...

By Matt 5 years ago
Go to File -> Preferences -> Object and yo...

By Theloniou... 5 years ago
@thelonious, I tried yes with this setting ...

By Matt 5 years ago
Once you change the "Customer Defaults", use the "...

By Theloniou... 4 years ago

Tapered thread design in NX - Can't use "Thread Feature" tool in NX for tapered thread

Last post by Dhaval, 4 years ago

Posts: 1

Views: 2590

How do you guys design tapered thread in NX? The "...

By Dhaval 4 years ago

NX Drafting Layer Use to Hide Parts from Certain Views

Last post by Broad, 4 years ago

Posts: 3

Views: 5416

I have, different part of the assembly in differen...

By Volker 5 years ago
I'm not clear what you want to do. However, if y...

By Theloniou... 5 years ago
In addition to this, after reset the layers for se...

By Broad 4 years ago

How to Add Display/Text Note to Model Component in NX

Last post by Broad, 4 years ago

Posts: 3

Views: 5187

Hi guys, I wanted to add some display note or la...

By Broad 4 years ago
Based on your requirement, we only know there is o...

By Yoda 4 years ago
Yes, this is, what I look for. Thank you

By Broad 4 years ago

Custom View ,that update with reference changes

Last post by Dhaval, 4 years ago

Posts: 5

Views: 4778

I'm trying to save a view for the model that get d...

By Matt 5 years ago
Did you find a method that custom saved view updat...

By Erdal 4 years ago
There is workaround for this. You can use "Sketch ...

By Yoda 4 years ago
Great tips.!, this will help to save my some hassl...

By Erdal 4 years ago
This view only updates within the modeling environ...

By Dhaval 4 years ago

Page 1 / 3 Next

61 Forums
322 Topics
1,307 Posts
9 Online
299 Members

Forum Icons: Forum contains no unread posts Forum contains unread posts

Topic Icons: Not Replied Replied Active Hot Sticky Unapproved Solved Private Closed

Powered by wpForo version 3.1.0

About Us

We bring you the best CAD related information and knowledge. As a engineering team, which mainly in the field of Mechanical, Manufacturing, Product Development, Industrial,& Architectural. Our aim is share our experience on design & 3D modeling fields and give chance to everyone to get benefit of it.
Read More

Copyright © 2019 - 2025 WiYa3D.com All rights reserved. Unauthorized reproduction or linking forbidden without expressed written permission. Registration on or use of this site constitutes acceptance of our Privacy Policy / Forum Rule & Posting Policies

No Result

View All Result

Login
Sign Up